APPS2car Universal 360° Rotation Car Phone Holder — a universal air-vent phone mount from APPS2CAR that grips any smartphone between 4.7 and 6.8 inches and holds it at whichever angle you need. The 360° ball joint swings the screen from portrait navigation to landscape in one movement, and the spring-loaded cradle keeps the phone steady over rough road surfaces.
Why it is worth fitting
Phone mounts usually fail in one of two ways. A suction cup lets go on a hot dashboard, leaving a ring of residue on the glass; a clamp rattles loose over broken tarmac until the phone is pointing at the floor. This holder sidesteps both problems by anchoring to the air-vent louvre and gripping the phone with a spring cradle instead of adhesive. Nothing is stuck to the windscreen or the trim, the phone sits at roughly eye level, and because it hangs in front of the vent the airflow keeps it cool on a long summer drive — which matters if you are running navigation with the screen at full brightness.
Key features
- Spring cradle accepts smartphones from 4.7″ to 6.8″ — most current phones including large-screen models
- 360° ball joint rotates freely, so you can switch between portrait and landscape without removing the phone
- Mounts on the air-vent louvre: no suction cup, no adhesive pad, no residue left on glass or dashboard
- Spring-loaded clamp holds firmly over speed bumps and uneven surfaces, and releases with one hand
- Anti-slip contact pads protect the phone casing from scuffs and stop it rotating in the cradle
- Works on both horizontal and vertical vent blades, so it suits almost any dashboard layout
- Vent mounting keeps the phone in the airflow, which helps prevent overheating during navigation
- Compact enough to leave fitted permanently — it does not obstruct the view through the windscreen
Specifications
| Brand | APPS2CAR |
|---|---|
| Model number | H6S-AV6S |
| Material | ABS |
| Mounting type | Air vent |
| Phone size supported | 4.7 – 6.8 inches |
| Compatible with | Universal — all major phone brands |
| Orientation | 360° rotation, portrait or landscape |
| Colour | Black |
| Country of origin | Guangdong, China |
Will it fit?
Fits virtually every car with an air-vent louvre, whether the blades run horizontally or vertically. The cradle is spring-loaded rather than shaped to a specific handset, so the same holder covers most phone and vehicle combinations. The only measurement that matters is your phone: check its width rather than its screen size if it is in a bulky case.
Fitting and first use
Clip the mounting foot over one vent blade — choose a central vent for the best viewing angle, and one that is not directly in front of a passenger airbag. Push it until the clips seat on both sides of the blade. Loosen the ball joint slightly, set the phone in the cradle at the angle you want, then tighten. To release the phone, squeeze the two side arms together and lift it out. No tools are needed and the whole thing takes under a minute, with nothing to charge or wire in.
Care and maintenance
Wipe the pads with a damp cloth if they pick up dust, since grit on the contact points is what causes a phone to slip. Check the vent clips are still tight once a season — repeated removal and refitting will eventually loosen them. Do not force the cradle open wider than the 6.8-inch maximum; over-stretching is the usual cause of a spring losing its tension. Remove the holder before cleaning the dashboard with silicone-based products, which can harden the plastic.
Frequently asked questions
Will it hold a phone in a thick case?
Measure the fitted phone across its widest point, case included. Anything up to roughly 6.8 inches wide will fit. Very thick rugged cases, such as waterproof or battery cases, may be too wide.
Does it work with a vertical vent?
Yes. The mounting foot grips both horizontal and vertical blades. On vertical vents the holder sits at a slightly different angle, which is why the ball joint rotates through a full 360 degrees.
Will it block the heater or air conditioning?
It covers part of one vent. Most people find the remaining airflow is more than enough, and in summer having cool air on the phone while it runs navigation is an advantage.
Can I leave it on the car permanently?
Yes. The clamp grips the vent blade, so it stays put. It does not obstruct your view of the road and does not leave any adhesive behind if you decide to move it.
SKU: AP-001 | Category: Car Phone Holder
Delivery is a flat €12 per order. See our Returns & Exchanges page for delivery times, your 14-day right of withdrawal and the 2-year legal guarantee of conformity.
Reviews
There are no reviews yet.